Yea, I just restore using the “Raw
Partition Backups” selection under Restore type. It’s worked fine
so far. The biggest pain is that the drive c-t-d names don’t match up to
each other. Our disk guy handles the mapping between the Sun side and HP side.
Eventually we would like to get everything over to HP to eliminate the
confusion.
Wayne BeDour
Unix System Administrator
PH: 313-593-9876
Internet: wbedour AT lear DOT com
From: Jeff Lightner
[mailto:jlightner AT water DOT com]
Sent: Monday, September 08, 2008
11:09 AM
To: BeDour, Wayne;
ueli.schweizer AT agite-software DOT com; veritas-bu AT mailman.eng.auburn DOT edu
Subject: RE: [Veritas-bu] Need a
command line command to change theBackup Selection for Policies
Interesting setup. Have you tested
restores doing this?
We do the same here for HP-UX to HP-UX
BCVs and I’ve done the same for Solaris to Solaris BCVs but this is the
first I’ve seen of Solaris to HP-UX.
From: BeDour, Wayne
[mailto:WBedour AT lear DOT com]
Sent: Monday, September 08, 2008
10:45 AM
To: Jeff Lightner;
ueli.schweizer AT agite-software DOT com; veritas-bu AT mailman.eng.auburn DOT edu
Subject: RE: [Veritas-bu] Need a
command line command to change theBackup Selection for Policies
We are mounting up disk to a Sun server,
syncing and breaking the bcv’s and mounting them up to our HP master
server. We are then backing up the raw devices.
Wayne BeDour
Unix System Administrator
PH: 313-593-9876
Internet: wbedour AT lear DOT com
From: Jeff Lightner
[mailto:jlightner AT water DOT com]
Sent: Monday, September 08, 2008
8:53 AM
To:
ueli.schweizer AT agite-software DOT com; BeDour, Wayne;
veritas-bu AT mailman.eng.auburn DOT edu
Subject: RE: [Veritas-bu] Need a
command line command to change theBackup Selection for Policies
Are you doing raw device backups?
I’m wondering why you’d be using disk addresses on
HP-UX. Even with raw devices if they’re on LVM or VxVM you’d
be better off backing up the raw LV than the underlying disks.
From:
veritas-bu-bounces AT mailman.eng.auburn DOT edu
[mailto:veritas-bu-bounces AT mailman.eng.auburn DOT edu] On Behalf Of Ueli Schweizer
Sent: Monday, September 08, 2008
8:26 AM
To: 'BeDour, Wayne';
veritas-bu AT mailman.eng.auburn DOT edu
Subject: Re: [Veritas-bu] Need a
command line command to change theBackup Selection for Policies
Use bpplinclude
Regards,
From: veritas-bu-bounces AT mailman.eng.auburn DOT edu
[mailto:veritas-bu-bounces AT mailman.eng.auburn DOT edu] On Behalf Of BeDour, Wayne
Sent: Monday, September 08, 2008
9:19 AM
To:
veritas-bu AT mailman.eng.auburn DOT edu
Subject: [Veritas-bu] Need a
command line command to change the Backup Selection for Policies
Our environment NBU 6.5, HP-UX 11.31. I’ve got a
ton of policies that I need to change the Backup Selections. They are all
disk addresses like c0t3d10. To avoid typo’s I’d like to
script the changes. I’ve always set up or changed policies via the
gui so I don’t know the command line commands that are invoked.
Anyone know what command line commands are needed to change the Backup
Selection portion of a Policy?
Thanks in advance…
Wayne BeDour
Unix System Administrator
PH: 313-593-9876
Internet: wbedour AT lear DOT com
**********************
** LEGAL DISCLAIMER **
**********************
This E-mail message and any attachments may contain
legally privileged, confidential or proprietary
information. If you are not the intended recipient(s),
or the employee or agent responsible for delivery of
this message to the intended recipient(s), you are
hereby notified that any dissemination, distribution
or copying of this E-mail message is strictly
prohibited. If you have received this message in
error, please immediately notify the sender and
delete this E-mail message from your computer.
|
----------------------------------
CONFIDENTIALITY NOTICE: This e-mail may contain privileged or confidential
information and is for the sole use of the intended recipient(s). If you are
not the intended recipient, any disclosure, copying, distribution, or use of
the contents of this information is prohibited and may be unlawful. If you have
received this electronic transmission in error, please reply immediately to the
sender that you have received the message in error, and delete it. Thank you.
----------------------------------