[Veritas-bu] Eight new SDLT320 drives not being recognzied by NBU Datacenter 3 .4
2004-05-05 12:56:52
Subject: |
[Veritas-bu] Eight new SDLT320 drives not being recognzied by NBU Datacenter 3 .4 |
From: |
gary.andresen AT pnwdata DOT com (Gary Andresen) |
Date: |
Wed, 5 May 2004 09:56:52 -0700 |
I assume the SCSI Bridge is a re-badged crossroads, make sure it's set up
for indexed mode.
Gary Andresen
Impossible Happens, Plan Ahead
Pacific Northwest Data Inc.
Tel: 503.701.5185
Fax: 503.692.3910
gary.andresen AT pnwdata DOT com
www.pnwdata.com
> -----Original Message-----
> From: veritas-bu-admin AT mailman.eng.auburn DOT edu [mailto:veritas-bu-
> admin AT mailman.eng.auburn DOT edu] On Behalf Of David Cecchino
> Sent: Wednesday, May 05, 2004 7:39 AM
> To: Hardt, Jon
> Cc: Veritas-Bu (E-mail)
> Subject: RE: [Veritas-bu] Eight new SDLT320 drives not being recognzied
> by NBU Datacenter 3 .4
>
> Hi ,
>
> You need to check your devlink.tab and make sure it is in your sg.links
> file when you create your sg devices.
>
> On Wed, 5 May 2004, Hardt, Jon wrote:
>
> > Hmmm... I wonder if you might be right. I doubt its a coincidnce that
> the
> > only LUNS that work are LUN 0 on their respective targets. When I
> edited my
> > st.conf file, I used 5 LUNs (zero through four) for each target; I'm
> > wondering if maybe I should only use one LUN (LUN 0) for each target
> > (basically the st.conf default with the wide SCSI targets uncommented).
> >
> > -----Original Message-----
> > From: Mike Ekholm [mailto:ekholm AT ekholm DOT org]
> > Sent: Wednesday, May 05, 2004 2:00 AM
> > To: Craig Richmond
> > Cc: Mike Ekholm; Veritas-Bu (E-mail)
> > Subject: Re: [Veritas-bu] Eight new SDLT320 drives not being recognzied
> > by NBU Datacenter 3 .4
> >
> >
> > On Wed, May 05, 2004 at 08:16:46AM +0100, Craig Richmond wrote:
> > > At 1:44 -0500 5/5/04, Mike Ekholm wrote:
> > > >The no device or address tells me that tar is not going to do crap,
> > sgscan
> > > >looking down the path can see the drives fine, but at this point
> solaris
> > > >can not see anything.
> > > >
> > > >I have never used a tape device that was not configured as lun 0, is
> > > >this supported on solaris?
> > >
> > > /kernerl/drv/st.conf
> > >
> > > Just like sd.conf
> > >
> > > name="st" class="scsi"
> > > target=0 lun=0;
> > >
> > > name="st" class="scsi"
> > > target=1 lun=0;
> > >
> > > name="st" class="scsi"
> > > target=2 lun=0;
> > >
> > > name="st" class="scsi"
> > > target=3 lun=0;
> > >
> >
> > Yeah, that is what I am use to seeing, every tape device as a lun 0 :-)
> >
> >
> > -Mike Ekholm
> > --
> > Mike Ekholm, UNIX Sys Admin - ekholm AT ekholm DOT org
> > web: http://www.ekholm.org ham: kc0mpu irc: Nalez
> > ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
> > UNIX - The Swiss army knife of software.
> >
> > _______________________________________________
> > Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
> > http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
> >
> _______________________________________________
> Veritas-bu maillist - Veritas-bu AT mailman.eng.auburn DOT edu
> http://mailman.eng.auburn.edu/mailman/listinfo/veritas-bu
|
|
|